The directive sets the DSCP value in transmitted NTP packets, which can
be useful in local networks where switches/routers are configured to
prioritise packets with specific DSCP values.
If the daemon transmit timestamp is saved for processing of a future
response or responding in the interleaved mode, get a more accurate
timestamp right before calling NIO_SendPacket(). Avoid unnecessary
reading of the clock for the transmit timestamp in the packet (i.e.
in interleaved modes and client basic mode).
This should improve accuracy and stability when authentication is
enabled in the client and symmetric basic modes and also interleaved
modes if kernel/hardware timestamps are not available.
Add binddevice, bindacqdevice, and bindcmddevice directive to specify
the interface for binding the NTP server, NTP client, and command socket
respectively.
Instead of making the initial burst only once and immediately after
chronyd start (even when iburst is specified together with the offline
option), trigger the burst whenever the connectivity changes from
offline to online.
Add -p option to chronyd to print lines from the configuration as they
are parsed and exit. It can be used to verify the syntax and get the
whole configuration when it is split into multiple files.
Instead of sharing the NTP rate limiting with NTS-KE, specify a new
service for NTS-KE and use it in the NTS-KE server.
Add ntsratelimit directive for configuration.
Add a new field to the CLIENT_ACCESSES_BY_INDEX request to specify the
minimum number of NTP or cmdmon packets for a client to be reported.
Add -p option to the chronyc clients command to specify the threshold
(by default 0). This option can be used to minimize the number of cmdmon
requests when interested only in clients sending a large number
of requests.
Add a flag to the CLIENT_ACCESSES_BY_INDEX request to reset the
NTP/cmdmon hits/dropped counters after reporting the current values.
Add -r option to the chronyc clients command to perform the reset. This
should make it easier to find clients that send large number of requests
over short periods of time.
Add a confdirs directive to include *.conf files from multiple
directories. If a file with the same name exists in multiple
directories, only the first one in the order of the specified
directories will be included.
When authentication is enabled for an NTP source, unauthenticated NTP
sources need to be disabled or limited in selection. That might be
difficult to do when the configuration comes from different sources
(e.g. networking scripts adding servers from DHCP).
Define four modes for the source selection to consider authentication:
require, prefer, mix, ignore. In different modes different selection
options (require, trust, noselect) are added to authenticated and
unauthenticated sources.
The mode can be selected by the authselectmode directive. The mix mode
is the default. The ignore mode enables the old behavior, where all
sources are used exactly as specified in the configuration.
The reset command drops all measurements and switches the reference to
the unsynchronised state. This command can help chronyd with recovery
when the measurements are known to be no longer valid or accurate, e.g.
due to moving the computer to a different network, or resuming the
computer from a low-power state (which resets the system clock).
Add -a option to the sources and sourcestats commands to print all
sources, including those that don't have a resolved address yet. By
default, only sources that have a real address are printed for
compatibility. Remove the "210 Number of sources" messages to avoid
confusion. Also, modify the ntpdata command to always print only sources
with a resolved address.
When resolving of a pool name succeeds, don't remove the remaining
unresolved sources, i.e. try to get all maxsources (default 4) sources,
even if it takes multiple DNS requests.
Add a new command to print the original name of a source specified by
address. This could be useful in scripts to avoid having to run the
sources command with and without -N.
Add -N option to chronyc to print the original names by which the
sources were specified instead of using reverse DNS lookup. The option
works in the sources, sourcestats and tracking commands.
Modify the request for adding a source to provide the name of the source
instead of its address (resolved in chronyc) in order to enable chronyd
to replace the source, support an "add pool" command, and enable an NTS
client to verify the server's certificate.
The name resolving does not block the response. Success is indicated
even if the name cannot be resolved, or a source with the same address
is already present.
To prevent unresolvable names from getting to chronyd, chronyc does not
send the request if it could not resolve the name itself (assuming they
are both running on the same host using the same resolver).
Allow a cipher (AES128 or AES256) to be specified as the type of a key
in the key file to authenticate NTP packets with a CMAC instead of the
NTPv4 (RFC 5905) MAC using a hash function. This follows RFC 8573.
An analysis by Tim Ruffing [1] shows that a length extension attack
adding valid extension fields to NTPv4 packets is possible with some
specific key lengths and hash functions using little-endian length like
MD5 and RIPEMD160.
chronyd currently doesn't process or generate any extension fields, but
it could be a problem in future when a non-authentication extension
field is supported.
Drop support for all RIPEMD functions as they don't seem to be secure in
the context of the NTPv4 MAC. MD5 is kept only for compatibility.
[1] https://mailarchive.ietf.org/arch/msg/ntp/gvibuB6bTbDRBumfHNdJ84Kq4kA
Setting maxsamples to 1 or 2 prevented the source from being selected as
the regression would always fail. Handle this as a special case with
disabled frequency tracking in order to enable a fast reference update
with the -q/-Q option.
