If no CFLAGS are specified, check if common security hardening options
are supported and add them to the CFLAGS/LDFLAGS. These are typically
enabled in downstream packages, but users compiling chrony from sources
with default CFLAGS should get hardened binaries too.
macOS 10.13 will implement the ntp_adjtime() system call, allowing
better control over the system clock than is possible with the existing
adjtime() system call. chronyd will support both the older and newer
calls, enabling binary code to run without recompilation on macOS 10.9
through macOS 10.13.
Early releases of macOS 10.13 have a very buggy adjtime() call. The
macOS driver tests adjtime() to see if the bug has been fixed. If the
bug persists then the timex driver is invoked otherwise the netbsd
driver.
New timestamping options may be available in kernel 4.13. They can be
used to get the index of the interface which timestamped incoming packet
together with its length at layer 2, enable simultaneous SW and HW TX
timestamping, and enable a new RX filter for NTP packets.
Move the res_init() call from do_name_to_ipaddress() into a separate
privops operation. Use it in ntp_sources and avoid unnecessary
res_init() calls in the main thread.
Add a new directive to specify interfaces which should be used for HW
timestamping. Extend the Linux ntp_io initialization to enable HW
timestamping, configure the RX filter using the SIOCSHWTSTAMP ioctl,
open their PHC devices, and track them as hwclock instances. When
messages with HW timestamps are received, use the PTP_SYS_OFFSET ioctl
to make PHC samples for hwclock.
Enable SCM_TIMESTAMPING control messages and the socket's error queue in
order to receive our transmitted packets with a more accurate transmit
timestamp. Add a new file for Linux-specific NTP I/O and implement
processing of these messages there.
Add support for authenticating MS-SNTP responses in Samba (ntp_signd).
Supported is currently only the old MS-SNTP authenticator field. It's
disabled by default. It can be enabled with the --enable-ntp-signd
configure option and the ntpsigndsocket directive, which specifies the
location of the Samba ntp_signd socket.
Split and convert the manual into four AsciiDoc documents, a document
about installation and three documents in the manpage type for
chrony.conf, chronyd and chronyc. The minimal man pages that were
maintained separately from the manual are replaced by full man pages
generated from AsciiDoc. Info files will no longer be provided.
Some parts of the manual are rewritten, updated or trimmed. The
introduction chapter is partially merged with README. The chapter about
typical operating scenarios is included in the chrony.conf man page.
Enable the PRV_Name2IPAddress() function with seccomp support and start
the helper process before loading the seccomp filter (but after dropping
root privileges). This will move the getaddrinfo() call outside the
seccomp filter and should make it more reliable as the list of required
system calls won't depend on what glibc NSS modules are used on the
system.
Prepare a list of required privileged operations first and from that
define the PRIVOPS macros. This will reduce the amount of code that will
be needed when the privileged helper is used on other platforms.
Add a function to fill a buffer with random bytes which uses a better
PRNG than random(). Use arc4random() if it's available on the system.
Fall back to reading from /dev/urandom, which should be available on
all currently supported systems.
Remove driver functions based on adjtime() and switch to the new timex
driver. The kernel allows the timex frequency to be set in the full
range of int32_t, which gives a maximum frequency of 32768 ppm. Round
the limit to 32500 ppm.
- a feature test macro is needed to get msg_control in struct msghdr
- variables must not be named sun to avoid conflict with a macro
- res_init() needs -lresolv
- configure tests for IPv6 and getaddrinfo need -lsocket -lnsl
- pid_t is defined as long and needs to be cast for %d format
Check if the C compiler works to get a useful error message when it
doesn't or it's missing. If the CC environment variable is not set, try
gcc and then cc.
Switch from the SunOS adjtime() based driver to the timex driver.
There is no FreeBSD-specific code, so call SYS_Timex_Initialise()
and SYS_Timex_Finalise() directly from sys.c.
