Add two reserved fields initialized to zero to the new REQ_LOCAL3
command to allow adding more options (e.g. delay in activation) without
changing the command number again.
This option sets an activating root distance for the local reference. The
local reference will not be used until the root distance drops below the
configured value for the first time. This can be used to prevent the local
reference from being activated on a server which has never been synchronised
with an upstream server. The default value of 0.0 causes no activating
distance to be used, such that the local reference is always eligible for
activation.
If the network correction is known for both the request and response,
and their sum is not larger that the measured peer delay, allowing the
transparent clocks to be running up to 100 ppm faster than the client's
clock, apply the corrections to the NTP offset and peer delay. Don't
correct the root delay to not change the estimated maximum error.
Rename the exp1 extension field to exp_mono_root (monotonic timestamp +
root delay/dispersion) to better distinguish it from future experimental
extension fields.
Update the serverstats response to use the new 64-bit integers.
Don't define a new value for the response as it already had an
incompatible change since the latest release (new fields added for
timestamp counters).
Add a structure for 64-bit integers without requiring 64-bit alignment
to be usable in CMD_Reply without struct packing.
Add utility functions for conversion to/from network order. Avoid using
be64toh() and htobe64() as they don't seem to be available on all
supported systems.
Add a new test for maximum delay using a long-term estimate of a
p-quantile of the peer delay. If enabled, it replaces the
maxdelaydevratio test. It's main advantage is that it is not sensitive
to outliers corrupting the minimum delay.
As it can take a large number of samples for the estimate to reach the
expected value and adapt to a new value after a network change, the
option is recommended only for local networks with very short polling
intervals.
Add "extfield F323" option to include the new extension field in
requests. If the server responds with this field, use the root
delay/dispersion and monotonic timestamp. Accumulate changes in the
offset between the monotonic and real-time receive timestamps and use
it for the correction of previous offsets in sourcestats. In the
interleaved mode, cancel out the latest change in the offset in
timestamps of the previous request and response, which were captured
before the change actually happened.
Report the number of received interleaved requests and current timestamp
count with their span.
Expand the serverstats description in chronyc man page.
When separate client and server instances of chronyd are running on one
computer (e.g. for security or performance reasons) and are synchronized
to each other, the server instance provides a reference ID based on the
local address used for synchronization of its NTP clock, which breaks
detection of synchronization loops for its own clients.
Add a "copy" option to specify that the server and client are closely
related, no loop can form between them, and the client should assume the
reference ID and stratum of the server to fix detection of loops between
the server and clients of the client.
The selection options returned as flags are not reported by the
client and will be better reported in a separate command with other
selection-specific data.
Add a new field to the CLIENT_ACCESSES_BY_INDEX request to specify the
minimum number of NTP or cmdmon packets for a client to be reported.
Add -p option to the chronyc clients command to specify the threshold
(by default 0). This option can be used to minimize the number of cmdmon
requests when interested only in clients sending a large number
of requests.
Add a flag to the CLIENT_ACCESSES_BY_INDEX request to reset the
NTP/cmdmon hits/dropped counters after reporting the current values.
Add -r option to the chronyc clients command to perform the reset. This
should make it easier to find clients that send large number of requests
over short periods of time.
The reset command drops all measurements and switches the reference to
the unsynchronised state. This command can help chronyd with recovery
when the measurements are known to be no longer valid or accurate, e.g.
due to moving the computer to a different network, or resuming the
computer from a low-power state (which resets the system clock).
Allow the nts and ntsport options to be specified for sources added from
chronyc. This is an incompatible change in the request, but there was no
release using the new REQ_ADD_SOURCE command yet.
Specify a new request to get the name of the NTP source corresponding to
an address, which was originally specified in the configuration file or
chronyc add command.
Modify the request for adding a source to provide the name of the source
instead of its address (resolved in chronyc) in order to enable chronyd
to replace the source, support an "add pool" command, and enable an NTS
client to verify the server's certificate.
The name resolving does not block the response. Success is indicated
even if the name cannot be resolved, or a source with the same address
is already present.
To prevent unresolvable names from getting to chronyd, chronyc does not
send the request if it could not resolve the name itself (assuming they
are both running on the same host using the same resolver).
The onoffline command tells chronyd to switch all sources to the online
or offline status according to the current network configuration. A
source is considered online if it is possible to send requests to it,
i.e. a route to the network is present.
Make the length of responses containing manual samples constant to
simplify the protocol. It was the only type of response that had a
variable length.
This reverts commit 2343e7a89c.
When the burst option is specified in the server/pool directive and the
current poll is longer than the minimum poll, initiate on each poll a
burst with 1 good sample and 2 or 4 total samples according to the
difference between the current and minimum poll.
