Specify maxpoll for HW timestamping (default minpoll + 1) to track the
PHC well even when there is little NTP traffic on the interface. After
each PHC reading schedule a timeout according to the maxpoll. Polling
between minpoll and maxpoll is still triggered by HW timestamps.
Wait for the first HW timestamp before adding the timeout to avoid
polling PHCs on interfaces that are enabled in the configuration but
not used for NTP. Add a new scheduling class to separate polling of
different PHCs to avoid too long intervals between processing I/O
events.
In some cases even the new timeout of 1 millisecond is not sufficient to
get all HW TX timestamps. Add a new directive to allow users to
specify longer timeouts.
After dropping root privileges, log a warning message if chronyd
doesn't have read access or has (unnecessary) write access to the
files containing symmetric and server NTS keys.
Allow messages to have severity set to INFO or DEBUG depending on the
context in which they are made to allow logging important changes made
from chronyc or sourcefile, but not spam the system log if those changes
are normally expected (e.g. specified in the config).
Add "local" option to specify that the reference clock is an
unsynchronized clock which is more stable than the system clock (e.g.
TCXO, OCXO, or atomic clock) and it should be used as a local standard
to stabilize the system clock.
Handle the local refclock as a PPS refclock locked to itself which gives
the unsynchronized status to be ignored in the source selection. Wait
for the refclock to get at least minsamples samples and adjust the clock
directly to follow changes in the refclock's sourcestats frequency and
offset.
There should be at most one refclock specified with this option.
Refactor the (cmd)allow/deny parser and make it more strict in what
input it accepts. Check the scanned numbers and require whole input to
be processed.
Move the parser to cmdparse to make it available to the client.
Allow NTP messages to be exchanged as a payload of PTP messages to
enable full hardware timestamping on NICs that can timestamp PTP packets
only. Implemented is the protocol described in this draft (version 00):
https://datatracker.ietf.org/doc/draft-mlichvar-ntp-over-ptp/
This is an experimental feature. It can be changed or removed in future.
The used PTP domain is 123 and the NTP TLV type is 0x2023 from the "do
not propagate" experimental range.
The ptpport directive enables NTP-over-PTP as a server and as a client
for all sources that have the port option set to the PTP port. The port
should be the PTP event port (319) to trigger timestamping in the
hardware.
The implementation is contained to ntp_io. It is transparent to
ntp_core.
Log an error message when adding of a source fails, e.g. due to the new
limit on number of sources, or when the same address is specified
multiple times.
When reading a *.sources file require that each line is termined by the
newline character to avoid processing an unfinished line, e.g. due to an
unexpected call of the reload command when the file is being written in
place.
Make the precision of the system clock configurable. This can be useful
on servers using hardware timestamping to reduce the amount of noise
added to the NTP timestamps and improve stability of NTP measurements.
The directive sets the DSCP value in transmitted NTP packets, which can
be useful in local networks where switches/routers are configured to
prioritise packets with specific DSCP values.
Add binddevice, bindacqdevice, and bindcmddevice directive to specify
the interface for binding the NTP server, NTP client, and command socket
respectively.
Instead of making the initial burst only once and immediately after
chronyd start (even when iburst is specified together with the offline
option), trigger the burst whenever the connectivity changes from
offline to online.
Add -p option to chronyd to print lines from the configuration as they
are parsed and exit. It can be used to verify the syntax and get the
whole configuration when it is split into multiple files.
Instead of sharing the NTP rate limiting with NTS-KE, specify a new
service for NTS-KE and use it in the NTS-KE server.
Add ntsratelimit directive for configuration.
Add a confdirs directive to include *.conf files from multiple
directories. If a file with the same name exists in multiple
directories, only the first one in the order of the specified
directories will be included.
When authentication is enabled for an NTP source, unauthenticated NTP
sources need to be disabled or limited in selection. That might be
difficult to do when the configuration comes from different sources
(e.g. networking scripts adding servers from DHCP).
Define four modes for the source selection to consider authentication:
require, prefer, mix, ignore. In different modes different selection
options (require, trust, noselect) are added to authenticated and
unauthenticated sources.
The mode can be selected by the authselectmode directive. The mix mode
is the default. The ignore mode enables the old behavior, where all
sources are used exactly as specified in the configuration.
Add "nocerttimecheck" directive to specify the number of clock updates
that need to be made before the time validation of certificates is
enabled. This makes NTS usable on machines that don't have a RTC.
This option is for indicating to chronyd that the reference clock is
kept in TAI and that chrony should attempt to convert from TAI to UTC by
using the timezone configured by the "leapsectz" directive.
