Add a new test for maximum delay using a long-term estimate of a
p-quantile of the peer delay. If enabled, it replaces the
maxdelaydevratio test. It's main advantage is that it is not sensitive
to outliers corrupting the minimum delay.
As it can take a large number of samples for the estimate to reach the
expected value and adapt to a new value after a network change, the
option is recommended only for local networks with very short polling
intervals.
Instead of waiting for the sample filter to accumulate the specified
number of samples and then deciding if the result is acceptable, count
missing samples and get the result after the specified number of polls.
This should work better when samples are dropped at a high rate. The
source and clock update interval will be stable as long as at least
one sample can be collected.
Latest versions of ethtool print only the shorter lower-case names of
capabilities and filters. Explain that chronyd doesn't synchronize the
PHC and refer to the new vclock feature of the kernel, which should be
used by applications that need a synchronized PHC (e.g. ptp4l and
phc2sys) in order to not interfere with chronyd.
Some PHCs that have a PPS input don't have configurable pins (their
function is hardcoded). Accept a negative pin index to skip the pin
configuration before requesting external timestamping.
Add "local" option to specify that the reference clock is an
unsynchronized clock which is more stable than the system clock (e.g.
TCXO, OCXO, or atomic clock) and it should be used as a local standard
to stabilize the system clock.
Handle the local refclock as a PPS refclock locked to itself which gives
the unsynchronized status to be ignored in the source selection. Wait
for the refclock to get at least minsamples samples and adjust the clock
directly to follow changes in the refclock's sourcestats frequency and
offset.
There should be at most one refclock specified with this option.
Allow sources to accumulate samples with the leap status set to not
synchronized. Define a new state for them to be ignored in the
selection. This is intended for sources that are never synchronized and
will be used only for stabilization.
For a long time, the Solaris support in chrony wasn't tested on a real
Solaris system, but on illumos/OpenIndiana, which was forked from
OpenSolaris when it was discontinued in 2010.
While Solaris and illumos might have not diverged enough to make a
difference for chrony, replace Solaris in the documentation with illumos
to make it clear which system is actually supported by the chrony
project.
If the xleave option is enabled, ignore the key option and the hash
length. Always use version 4 as the default to get interleaved responses
from new chrony servers.
Add "extfield F323" option to include the new extension field in
requests. If the server responds with this field, use the root
delay/dispersion and monotonic timestamp. Accumulate changes in the
offset between the monotonic and real-time receive timestamps and use
it for the correction of previous offsets in sourcestats. In the
interleaved mode, cancel out the latest change in the offset in
timestamps of the previous request and response, which were captured
before the change actually happened.
Report the number of received interleaved requests and current timestamp
count with their span.
Expand the serverstats description in chronyc man page.
Use the lowest bit of the server RX and TX timestamp as a flag
indicating RX timestamp. This allows the server to detect potential
interleaved requests without having to save all its RX timestamps. It
significantly reduces the amount of memory needed to support clients
using the interleaved mode if most of the server's clients are using the
basic mode (e.g. a public server).
Capture the TX timestamp on the first response to the request which has
the flag set to not further delay the first interleaved response.
False positives are possible with broken clients which set the origin
timestamp to something else than zero or the server RX or TX timestamp.
This causes an unnecessary RX timestamp to be saved and TX timestamp
captured and saved.
Allow NTP messages to be exchanged as a payload of PTP messages to
enable full hardware timestamping on NICs that can timestamp PTP packets
only. Implemented is the protocol described in this draft (version 00):
https://datatracker.ietf.org/doc/draft-mlichvar-ntp-over-ptp/
This is an experimental feature. It can be changed or removed in future.
The used PTP domain is 123 and the NTP TLV type is 0x2023 from the "do
not propagate" experimental range.
The ptpport directive enables NTP-over-PTP as a server and as a client
for all sources that have the port option set to the PTP port. The port
should be the PTP event port (319) to trigger timestamping in the
hardware.
The implementation is contained to ntp_io. It is transparent to
ntp_core.
A while back, support for memory locking and real-time scheduling was
added to more platforms. The chronyd documentation wasn't updated at
that time (chronyd.conf was). This patch fixes that.
The files are read after dropping root privileges. They need to be
readable by the chrony user. The error message "Could not set
credentials : Error while reading file." does not make this requirement
very obvious.
Add level "2" to enable a filter which blocks only specific system calls
like fork and exec* instead of blocking everything unknown. It should
be reliable with respect to changes in libraries, but it provides only a
very limited protection.
The NTS RFC requires the recipient of the Server Negotiation NTS-KE
record to handle the name as a fully qualified domain name. Add a
trailing dot if not present to force the name to be resolved as one.
When reading a *.sources file require that each line is termined by the
newline character to avoid processing an unfinished line, e.g. due to an
unexpected call of the reload command when the file is being written in
place.
When separate client and server instances of chronyd are running on one
computer (e.g. for security or performance reasons) and are synchronized
to each other, the server instance provides a reference ID based on the
local address used for synchronization of its NTP clock, which breaks
detection of synchronization loops for its own clients.
Add a "copy" option to specify that the server and client are closely
related, no loop can form between them, and the client should assume the
reference ID and stratum of the server to fix detection of loops between
the server and clients of the client.
