When the refresh command is issued, instead of trying to replace all
NTP sources as if they were unreachable or falsetickers, keep using the
current address if it is still returned by the resolver for the name.
This avoids unnecessary loss of measurements and switching to
potentially unreachable addresses.
Update the serverstats response to use the new 64-bit integers.
Don't define a new value for the response as it already had an
incompatible change since the latest release (new fields added for
timestamp counters).
In a non-tty session with chronyc it is not possible to detect the
end of the response without relying on timeouts, or separate responses
to a repeated command if using the -c option.
Add -e option to end each response with a line containing a single dot.
If AES-128-GCM-SIV is available on the client, add it to the requested
algorithms in NTS-KE as the first (preferred) entry.
If supported on the server, it will make the cookies shorter, which
will get the length of NTP messages containing only one cookie below
200 octets. This should make NTS more reliable in networks where longer
NTP packets are filtered as a mitigation against amplification attacks
exploiting the ntpd mode 6/7 protocol.
Add a new test for maximum delay using a long-term estimate of a
p-quantile of the peer delay. If enabled, it replaces the
maxdelaydevratio test. It's main advantage is that it is not sensitive
to outliers corrupting the minimum delay.
As it can take a large number of samples for the estimate to reach the
expected value and adapt to a new value after a network change, the
option is recommended only for local networks with very short polling
intervals.
Allow sources to accumulate samples with the leap status set to not
synchronized. Define a new state for them to be ignored in the
selection. This is intended for sources that are never synchronized and
will be used only for stabilization.
Report the number of received interleaved requests and current timestamp
count with their span.
Expand the serverstats description in chronyc man page.
For sources specified by an IP address, keep the original address as the
source's name and pass it to the NCR instance. Allow the sources to go
through the replacement process if their address has changed.
This will be useful with NTS-KE negotiation.
The IP-based source names are now provided via cmdmon. This means
chronyc -n and -N can show two different addresses for a source.
Add a new field to the CLIENT_ACCESSES_BY_INDEX request to specify the
minimum number of NTP or cmdmon packets for a client to be reported.
Add -p option to the chronyc clients command to specify the threshold
(by default 0). This option can be used to minimize the number of cmdmon
requests when interested only in clients sending a large number
of requests.
Add a flag to the CLIENT_ACCESSES_BY_INDEX request to reset the
NTP/cmdmon hits/dropped counters after reporting the current values.
Add -r option to the chronyc clients command to perform the reset. This
should make it easier to find clients that send large number of requests
over short periods of time.
The reset command drops all measurements and switches the reference to
the unsynchronised state. This command can help chronyd with recovery
when the measurements are known to be no longer valid or accurate, e.g.
due to moving the computer to a different network, or resuming the
computer from a low-power state (which resets the system clock).
Add -a option to the sources and sourcestats commands to print all
sources, including those that don't have a resolved address yet. By
default, only sources that have a real address are printed for
compatibility. Remove the "210 Number of sources" messages to avoid
confusion. Also, modify the ntpdata command to always print only sources
with a resolved address.
Add a new command to print the original name of a source specified by
address. This could be useful in scripts to avoid having to run the
sources command with and without -N.
Add -N option to chronyc to print the original names by which the
sources were specified instead of using reverse DNS lookup. The option
works in the sources, sourcestats and tracking commands.
Modify the request for adding a source to provide the name of the source
instead of its address (resolved in chronyc) in order to enable chronyd
to replace the source, support an "add pool" command, and enable an NTS
client to verify the server's certificate.
The name resolving does not block the response. Success is indicated
even if the name cannot be resolved, or a source with the same address
is already present.
To prevent unresolvable names from getting to chronyd, chronyc does not
send the request if it could not resolve the name itself (assuming they
are both running on the same host using the same resolver).
The onoffline command tells chronyd to switch all sources to the online
or offline status according to the current network configuration. A
source is considered online if it is possible to send requests to it,
i.e. a route to the network is present.
