If the -Q option is specified, disable by default pidfile, ntpport,
cmdport, Unix domain command socket, and clock control, in order to
allow starting chronyd without root privileges and/or when another
chronyd instance is already running.
The tai field in struct timex is a Linux-specific feature. It's possible
to read the current offset with ntp_gettime() (or ntp_gettimex() on
Linux), but apparently not all libc implementations support it.
Rework the code to save and adjust the last value instead of reading
the current value from the kernel.
Unlike in the basic mode, the peer with a higher stratum needs to wait
for a response before sending the next request in order to minimize the
delay of the measurement and error in the measured delay.
Slightly increase the delay adjustment to make it work with older chrony
versions.
Update the remote poll and remote stratum even for unsychronised peers,
and handle stratum of 0 as 16, so the peers work with the opposite
differences between their strata and can adjust their polling intervals
in order to interleave the packets.
Use the timezone specified by the leapsectz directive to get the
current TAI-UTC offset and set the offset of the system clock in order
to provide correct TAI time to applications using ntp_adjtime(),
ntp_gettime(), or clock_gettime(CLOCK_TAI).
Instead of repeatedly expanding the range of b with the same increment,
double the range on each iteration to speed up the expansion. Also, add
a sanity check for the interval.
The bisection always terminated after one iteration. Change the code to
check if the middle is different from the lower and upper limits as
suggested in the original recipe.
This fixes commit b14689d59b.
In order to stabilize the weights of refclock samples which have only
slightly different distances, don't allow the stddev value used in the
weight calculation to be smaller than the precision and also assign
weight of 1 to all samples which have distance < minimum + precision.
When parsing the include directive, call glob() with the GLOB_ERR and
GLOB_NOMAGIC flags, and abort with an error message when matching of the
pattern failed with other error than GLOB_NOMATCH.
This restores the original behavior of the directive when it didn't
allow patterns, but it will still not fail with patterns not matching
any files in an existing directory.
When the poll value in a client request is smaller than the server's NTP
rate limiting interval, set poll in the response to the rate limiting
interval to suggest the client to increase its polling interval.
This follows ntpd as a server. No current client implementation seems to
be increasing its interval by the poll, but it may change in the future.
Add an rxfilter option to the hwtimestamp directive to select which
received packets should be timestamped. It can be set to "none", "ntp",
or "all". The default value is ntp, which falls back to all when ntp is
not supported.
New timestamping options may be available in kernel 4.13. They can be
used to get the index of the interface which timestamped incoming packet
together with its length at layer 2, enable simultaneous SW and HW TX
timestamping, and enable a new RX filter for NTP packets.
Request SW timestamps with SCM_TIMESTAMPING even if HW timestamping is
enabled. This replaces SCM_TIMESTAMP(NS) for RX and enables TX SW
timestamping on interfaces that don't support HW timestamping (or don't
have it enabled) if another interface has HW timestamping enabled.
Don't give up when one of the addresses/hostnames specified by -h fails
to resolve in DNS_Name2IPAddress(), e.g. with the default setting try to
connect to ::1 even when 127.0.0.1 failed due to the -6 option.
This allows multiple options to be specified together and also may
options follow configuration directives on systems where getopt()
permutates the arguments.
Source selection uses the last event time as current time. If it was
called from a refclock which generates a sample in its poll function
(e.g. PHC), the sample time may be later than the event time. This
gives a negative elapsed time in SST_GetSelectionData() and possibly
also a negative root distance, which causes the source to be rejected as
a falseticker.
Use absolute value of the difference in order to always get a positive
root distance.
Add width option to the refclock directive to set expected width of
pulses in a PPS signal. The width adds a limit for the maximum offset
and root distance in order to reject PPS samples from wrong events, e.g.
PHCs which cannot be configured to timestamp only rising of falling
edges.
Add extpps driver option to the PHC refclock to enable external
timestamping of PPS signal and also options to configure the channel and
pin index. In this mode, the driver polling function accumulates samples
for hwclock, which is used to convert received timestamping events to
local time.
Add pps option to the refclock directive to force chronyd to treat any
refclock as a PPS refclock. This is intended for refclocks that may
provide time off by a whole number of seconds due to missing or wrong
TAI/GPS->UTC conversion.
Split RCL_AddPulse() in order to provide a new function for refclock
drivers which can make PPS samples without having raw system time, e.g.
from PHC timestamps.
